HFBoards

Go Back   HFBoards > General Hockey Discussion > The Rink
Mobile Hockey's Future Become a Sponsor Site Rules Support Forum vBookie Page 2
Notices

The Rink For the not so ready for prime-time players, coaches, referees, and the people that have to live with them. Discuss experiences in local leagues, coaching tips, equipment, and training.

Bauer One100 Sticks

Reply
 
Thread Tools
Old
07-08-2011, 04:11 AM
  #1
Pez68
Registered User
 
Pez68's Avatar
 
Join Date: Mar 2010
Location: Chicago, IL
Posts: 1,770
vCash: 500
Bauer One100 Sticks

Not sure how many people are aware of this, but I thought I would share some information I recently came across in regards to this stick. If you break your One100 in the shaft, don't throw it away. You can actually pull the blades right out of these, and it is relatively easy to do. Takes roughly 15 minutes. They fit perfectly in any standard shafts as well.

Both of the One100s I had, broke right above the blade/shaft fuse point. If you look down into the broken shaft towards the blade, you will actually see where the blade was inserted into the shaft. Cut down to that point, making sure not to cut the actual blade hosel. Having a reference two-piece blade helps for measurement. Then you want to cut down the middle of the shaft so it splits. I actually used a dremel and a small cutting wheel to make this cut, being careful not to cut too deep, and hit the blade hosel. You only want to cut through the outer layer of composite that the blade is inserted into. Cut through this outer layer roughly 3 inches down from the shaft end of the blade, towards the blade. Heat up the blade/shaft in that area, and insert a flathead screwdriver. It separates pretty easily at this point. Once you have it split, you can cut the shaft off of the blade at the point you want the blade hosel to stop.(approx. 3 inches of hosel) On the P92 - 87 Flex, this is right at the P on the backhand side, or the X on the forehand side. Voila! You have a high quality blade to insert into a shaft of your choice.

I have done this twice, and both blades perform fantastically. Sure beats buying a $60 TotalOne blade.

One of these blades is in a TotalOne that the blade broke on. Flipped it over and put it in, and I can't tell the difference. The other is in a One95, same situation. Both sticks feel and shoot great.

Just something to consider if you're cheap like me, and can't seem to stop breaking sticks.


Last edited by Pez68: 07-08-2011 at 10:58 AM.
Pez68 is offline   Reply With Quote
Old
07-08-2011, 09:20 AM
  #2
AIREAYE
Moderator
 
AIREAYE's Avatar
 
Join Date: Jun 2009
Country: China
Posts: 4,497
vCash: 500
Good work Pez, the same can be done for a number of OPS which are actually fused 2-pieces. The Dolomites come to mind; it's just a crapload of work to get the blade out.

And it's 'Voila' (a french word) , not 'wallah'

AIREAYE is offline   Reply With Quote
Old
07-08-2011, 10:58 AM
  #3
Pez68
Registered User
 
Pez68's Avatar
 
Join Date: Mar 2010
Location: Chicago, IL
Posts: 1,770
vCash: 500
Fixed. Thanks.

I was aware you could do this with other sticks as well. It's just, the blade in the One100 is really, really good. Better than most blades I've used for two-pieces. I would never go through this trouble for a crappy Easton blade, and I hear Warrior blades go soft pretty quickly too.

Pez68 is offline   Reply With Quote
Old
07-08-2011, 02:20 PM
  #4
AIREAYE
Moderator
 
AIREAYE's Avatar
 
Join Date: Jun 2009
Country: China
Posts: 4,497
vCash: 500
The blade cores for the Supreme lineup (excluding the T1, high & mid-pricepoint sticks only) and the Vapor lineup are the same, so the puck feel for the One100 is going to be similar to the X:60 and so on

AIREAYE is offline   Reply With Quote
Reply

Forum Jump


Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 03:39 PM.

monitoring_string = "e4251c93e2ba248d29da988d93bf5144"

vBulletin Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.
HFBoards.com is a property of CraveOnline Media, LLC, an Evolve Media, LLC company. 2016 All Rights Reserved.